scsi-config(8) - man - phpMan

Che Dong

scsi-config(8) Scsiinfo User's Guide scsi-config(8)

NAME
scsi-config - query information from a scsi device with a nice user interface

SYNOPSIS
scsi-config [device]

DESCRIPTION
scsi-config queries information from an scsi target with a nice Tcl/Tk user interface. If you
do not specify a device to query, scsi-config calculates a list of available devices and
prompts it to you.

By the nature of a graphical user interface, most things will explain them self. Basically,
scsi-config shows a list of buttons for certain mode pages which you may press. Those buttons
which you can press and the text windows with white backgrounds can be modified by you and
the modifications send back to the device.

In the main window there is a button to instruct the device to save the data in some non
volatile memory (if it supports it). Note that this will instruct the device to save the
Read-Write Error Recovery Page , Disconnect-Reconnect Page , Format Device Page , Caching
Page , and Control Mode Page in its NVRAM. Usually saving even a single of those should write
them all to the NVRAM, but you never know.

You can query the current, the factory default and the values in the NVRAM (which may not be
the current parameters) from the device.

Not all combinations of button toggles or all values are valid. In general, try to set them
and see which values the drive accepts. scsi-config rereads the device configuration immedi‐
ately, s.t. you see which values where accepted.

Also note that some disk drives are notched, and that those have an active notch (shown in
the main window) to which all your settings apply (at least those of notched pages, which are
also marked in slate gray). You can select the active notch to which your settings apply (and
to which the values refer) in the Notch Page.

For those devices which do not feature an NVRAM (generally removable media devices) and as a
kind of backup, you can save the current settings to a file. Actually the file will be a
/bin/sh script making the necessary scsiinfo(8) calls to set the saved parameters when exe‐
cuted.

There is also a nice Overview button which will query many details about the disk geometry
and draw them in a nice picture. This looks esp. nice for drives with many notches, that is
different regions on the disk with different tracks per sector settings. It is also very use‐
ful for notched drives as you can immediately select the mode pages for each notch.

SOME USAGE GUIDELINES
1. General Warning
Generally, do not modify settings you don't understand. It is useful to know the SCSI-
II specs mentioned below. Some setting may render the device unusable or even damage
it. Usually a power cycle resets the state (if you do not save the weird settings in
the NVRAM). Some settings affecting the assignment of logical sectors will render the
disk unusable until the next low level format.

2. On Write Caching
As an old warning, this does also mean you should not generally switch the write cache
on. At least on those drives where you have a choice at all. Reasons are twofold:

a) It is a priori unclear when the drive will actually perform the writes. This is
a bad thing when considering shutdown of your machine. On the other hand, it
seems sensible to assume that the drive will immediately write it's cache to
disk when it is idle (after all file systems are unmounted) and due to the size
of the on disk cache this will usually only need a few seconds after the shut‐
down (but the drive lamp will usually not glow, as it is mostly connected to
the host adapter (if you have a lamp at all) and it is not participating).

There is a SCSI command to flush the caches. Linux could call it prior to shut‐
ting down, spinning a disk down. Due to my knowledge this is not yet done
though.

b) As the writes are performed asynchronously, errors are reported asynchronously.
The disk might return an error at some simple read instruction related to a
write which was acknowledged OK several transactions ago. This generally con‐
fuses things and makes interpreting errors very difficult. Some devices are
known/said to not report write errors in this mode of operation at all.

Just imagine that at the point where a file system is unmounted, or a new re‐
movable media is detected it could tell: Oops, BTW, there was some write error
ago although I told you it was OK already.

Thus, when you run a disk in write cache mode, keep it in mind when weird error mes‐
sages occur and give the disk time to flush it's buffers at shutdown. Generally it
would be good if you knew more vendor specific details on how the disk operates in the
write cache mode.

3. Reassigning Bad Blocks Automatically
One of the nice features of SCSI disk is that they allow to remap bad blocks automati‐
cally as they are detected without any user intervention. However, you actually have
to enable this feature! It turned out that you can not generally assume a disk in
this mode. To enable this mode or check the settings, proceed as follows:

a) Go to the Read-Write Error Recovery Page. AWRE (Automatic Write Reallocation
Enable) and ARRE (Automatic Read Reallocation Enable) buttons enable the auto‐
matic reallocation.

In the same window, you can select the maximal retries performed. EER allows
the disk to do some Early Error Recovery which is fast (but might misdetect or
miscorrect data). A selected DCR button (Disable CoRrection Codes) disallows
the disk to use any error correction codes at all (thus the drive will have to
retry until it performs an error free read).

Usually a sector will be reallocated after even a single read retry or the
given number of failed write retries. When the sector cannot be recovered, it
is reallocated but the data is lost and an error is signalled.

The other buttons there apply to error reporting as well. TB Transmits the bad
Block together with the error, RC Reads Continuous, that is, does not pause a
read operation while retrying or using error code calculations to recover a bad
block (thus may return bad data). PER lets the disk report even recovered er‐
rors (Post ERror), DTE (Disable Transfer on Error) even breaks a running data
transmission when an error is detected.

b) Even when the reallocation is enabled, the disk must actually have some re‐
served areas where to remap the bad blocks. The Format Page controls this. Ei‐
ther a given number of Alternate Sectors Per LUN is set aside for the whole
disk or a given number of tracks is defined to be a zone and for each zone a
number of sectors or tracks is put aside. These alternate data areas are where
bad sectors are remapped.

Note that this page is very likely to apply only to the current notch on a
notched disk device.

If there are no, or not many alternate sectors reserved on your disk, you must
change these settings.

I found that those disks which allow to modify these settings are very often
set to no reserved sectors at all by the vendors, as this increases the disks
capacity. For the sake of stability, you should really modify these settings.

If you decide to modify the number of alternate sectors, you must

i) Save the parameters to the NVRAM of the disk.

ii) Low-level format the disk drive (and not erase the NVRAM during this op‐
eration).

to make the changes be effective.

c) Esp. when you set the disk to not report recovered errors (or when it is in a
write cache mode or something), and just as a general guideline, keep an eye on
the grown defects list where the disk will report all the remappings which took
place as your disk ages.

The old adventurers guide line applies: Save (Backup) Early, Save (Backup) Of‐
ten. Find the right time to replace your disk avoiding too much work recovering
your data.

BUGS
scsi-config could be enhanced by making better use of Tcl/Tk. I learned much about it during
my work on tk_scsiformat(8) and their would be much room for fixes and enhances. On other
hand, it fulfils it's purpose as it is quite nicely already.

As scsi-config makes heavy use of scsiinfo(8) all it's bugs (esp. on defect reading) apply.

FILES
/usr/lib/scsi/cache, /usr/lib/scsi/control, /usr/lib/scsi/disconnect, /usr/lib/scsi/error,
/usr/lib/scsi/format, /usr/lib/scsi/generic, /usr/lib/scsi/inquiry, /usr/lib/scsi/notch,
/usr/lib/scsi/overview, /usr/lib/scsi/peripheral, /usr/lib/scsi/rigid, /usr/lib/scsi/save-
changes, /usr/lib/scsi/save-file, /usr/lib/scsi/tworands, /usr/lib/scsi/verify (Tcl/Tk sub‐
routines used by scsi-config).
/dev/sd*
/dev/sg*
/dev/scd*
/dev/st*
/dev/nst*
/dev/rmt*
/dev/nrmt*

SEE ALSO
scsiinfo(8), scsiformat(8), tk_scsiformat(8), fdisk(8), sd(4),

Draft proposed
American National Standard
for information systems

SMALL COMPUTER SYSTEM INTERFACE - 2
(SCSI-2)

MARCH 9, 1990

AUTHORS
Eric Youngdale.
Michael Weller <eowmob AT exp-math.de>, Versions 1.5 & 1.7

scsiinfo 1.7 24 August 1997 scsi-config(8)