man > rescan-scsi-bus.sh(8)

RESCAN-SCSI-BUS.SH(1)                       User Commands                      RESCAN-SCSI-BUS.SH(1)



NAME
       rescan-scsi-bus.sh - script to add and remove SCSI devices without rebooting

SYNOPSIS
       rescan-scsi-bus.sh  [--alltargets]  [--attachpq3]  [-c]  [---channels=CLIST]  [--color]  [-d]
       [--flush] [-f] [--forceremove] [--forcerescan] [--help] [--hosts=HLIST] [--ids=TLIST]  [--ig‐
       nore-rev]  [--issue-lip]  [-i]  [--issue-lip-wait=SECS]  [-I SECS] [-l] [-L NUM] [--largelun]
       [--luns=LLIST] [-m] [--multipath] [--nooptscan] [--nosync] [--remove]  [--removelun2]  [--re‐
       size] [--sparselun] [--sync] [--update] [--version] [--wide] [HOST1 [HOST2 ...]]

OPTIONS
       Option are ordered by their long name. Those without a long name are ordered as if their sin‐
       gle letter was a long name.

       -a, --alltargets
              scan all targets, not just currently existing [default: disabled]

       --attachpq3
              tell kernel to attach sg to LUN 0 that reports PQ=3

       -c     enables scanning of channels 0 1   [default: 0 / all detected ones]

       --channels=CLIST
              scan only channel(s) in CLIST

       --color
              use coloured prefixes OLD/NEW/DEL

       -d     enable debug                       [default: 0]

       -f, --flush
              flush failed multipath devices     [default: disabled]

       --forceremove
              remove stale devices (DANGEROUS)

       --forcerescan
              remove and readd existing devices (DANGEROUS)

       -h, --help
              print usage message then exit

       --hosts=HLIST
              scan only host(s) in HLIST

       --ids=TLIST
              scan only target ID(s) in TLIST

       --ignore-rev
              ignore (firmware) revision change. This is the third text field (4 bytes  long)  in  a
              standard INQUIRY response.

       -i, --issue-lip
              issue a FibreChannel LIP reset     [default: disabled]

       -I SECS, --issue-lip-wait=SECS
              issue a FibreChannel LIP reset and then wait SECS seconds.

       -L NUM activates scanning for LUNs 0--NUM [default: 0]

       -l     activates scanning for LUNs 0--7   [default: 0]

       --largelun
              tell kernel to support LUNs > 7 even on SCSI2 devs

       --luns=NLIST
              scan only lun(s) in NLIST

       -m, --multipath
              update multipath devices           [default: disabled]

       --nooptscan
              don't stop looking for LUNs is 0 is not found

       --nosync
              do not issue a sync [default: sync if remove]

       -r, --remove
              enables removing of devices        [default: disabled]

       --reportlun2
              tell kernel to try REPORT_LUN even on SCSI2 devices

       -s, --resize
              look for resized disks and reload associated multipath devices, if applicable

       --sparselun
              tell kernel to support sparse LUN numbering

       --sync issue a sync [default: sync if remove]

       -u, --update
              look for existing disks that have been remapped

       -V, --version
              shows version string then exits. The version string is a numeric datestamp of the form
              YYYYMMDD.

       -w, --wide
              scan for target device IDs 0--15   [default: 0--7]

              Host numbers may thus be specified either directly on cmd line  (deprecated)  or  with
              the --hosts=LIST parameter (recommended).

       Arguments to options that end in LIST (e.g. TLIST) can have this form:
           A[-B][,C[-D]]...
       which is a comma separated list of single values and/or ranges (no spaces allowed).

SEE ALSO
       There  is  a  brief  descripion here: http://fibrevillage.com/storage/585-rescan-scsi-bus-sh-
       script-for-adding-and-removing-scsi-devices-without-rebooting

       sg3_utils Homepage: http://sg.danny.cz/sg



rescan-scsi-bus.sh                            July 2018                        RESCAN-SCSI-BUS.SH(1)