man > encoding::warnings

man perldoc info pydoc3 ri search

📛 Name

encoding::warnings - Warn on implicit encoding conversions

🚀 Quick Reference

Use Case	Command	Description
Detect implicit byte-to-unicode upgrades	use encoding::warnings;	⚠️ Enables warnings for silent upgrades (non‑fatal by default)
Make implicit upgrade warnings fatal	use encoding::warnings 'FATAL';	🚨 Raises exceptions instead of warnings
Silence warnings by assuming ISO‑8859‑1	use encoding 'iso-8859-1';	🔇 Restores default behaviour (no warnings)
Silence warnings by assuming UTF‑8	use encoding 'utf8';	🔇 Assumes all byte strings are UTF‑8
Upgrade all data to Unicode via IO layers	use open ':std', ':encoding(UTF-8)';	🔁 Converts all I/O to Unicode strings

⚠️ Notice: As of Perl 5.26.0 this module has no effect. The internal feature it used has been removed. See the NOTICE section below.

🏷️ Version

This document describes version 0.13 of encoding::warnings, released June 20, 2016.

⚠️ Notice

As of Perl 5.26.0, this module has no effect. The internal Perl feature that was used to implement this module has been removed. In recent years, much work has been done on the Perl core to eliminate discrepancies in the treatment of upgraded versus downgraded strings. In addition, the encoding pragma, which caused many of the problems, is no longer supported. Thus, the warnings this module produced are no longer necessary.

Hence, if you load this module on Perl 5.26.0, you will get one warning that the module is no longer supported; and the module will do nothing thereafter.

📋 Synopsis

use encoding::warnings;  # or 'FATAL' to raise fatal exceptions

utf8::encode($a = chr(20000));  # a byte-string (raw bytes)
$b = chr(20000);                # a unicode-string (wide characters)

# "Bytes implicitly upgraded into wide characters as iso-8859-1"
$c = $a . $b;

📖 Description

🔍 Overview of the problem

By default, there is a fundamental asymmetry in Perl's unicode model: implicit upgrading from byte‑strings to unicode‑strings assumes that they were encoded in ISO 8859‑1 (Latin‑1), but unicode‑strings are downgraded with UTF‑8 encoding. This happens because the first 256 codepoints in Unicode happens to agree with Latin‑1.

However, this silent upgrading can easily cause problems, if you happen to mix unicode strings with non‑Latin1 data – i.e. byte‑strings encoded in UTF‑8 or other encodings. The error will not manifest until the combined string is written to output, at which time it would be impossible to see where did the silent upgrading occur.

🕵️ Detecting the problem

This module simplifies the process of diagnosing such problems. Just put this line on top of your main program:

use encoding::warnings;

Afterwards, implicit upgrading of high‑bit bytes will raise a warning. Ex.: "Bytes implicitly upgraded into wide characters as iso-8859-1 at - line 7".

However, strings composed purely of ASCII code points (0x00..0x7F) will not trigger this warning.

You can also make the warnings fatal by importing this module as:

use encoding::warnings 'FATAL';

🔧 Solving the problem

Most of the time, this warning occurs when a byte‑string is concatenated with a unicode‑string. There are a number of ways to solve it:

• 🎯 Upgrade both sides to unicode‑strings
  If your program does not need compatibility for Perl 5.6 and earlier, the recommended approach is to apply appropriate IO disciplines, so all data in your program become unicode‑strings. See encoding, open and binmode in perlfunc for how.
• 🎯 Downgrade both sides to byte‑strings
  The other way works too, especially if you are sure that all your data are under the same encoding, or if compatibility with older versions of Perl is desired. You may downgrade strings with Encode::encode and utf8::encode. See Encode and utf8 for details.
• 🎯 Specify the encoding for implicit byte‑string upgrading
  If you are confident that all byte‑strings will be in a specific encoding like UTF‑8, and need not support older versions of Perl, use the encoding pragma:

use encoding 'utf8';

Similarly, this will silence warnings from this module, and preserve the default behaviour:

use encoding 'iso-8859-1';

However, note that use encoding actually had three distinct effects:

• 🔄 PerlIO layers for STDIN and STDOUT – similar to what open pragma does.
• 🔄 Literal conversions – turns all literal strings in your program into unicode‑strings (equivalent to a use utf8), by decoding them using the specified encoding.
• 🔄 Implicit upgrading for byte‑strings – silences warnings from this module, as shown above.

Because literal conversions also work on empty strings, it may surprise some people:

use encoding 'big5';

my $byte_string = pack("C*", 0xA4, 0x40);
print length $a;    # 2 here.
$a .= "";           # concatenating with a unicode string...
print length $a;    # 1 here!

In other words, do not use encoding unless you are certain that the program will not deal with any raw, 8‑bit binary data at all.

However, the Filter => 1 flavor of use encoding will not affect implicit upgrading for byte‑strings, and is thus incapable of silencing warnings from this module. See encoding for more details.

⚠️ Caveats

For Perl 5.9.4 or later, this module's effect is lexical.

For Perl versions prior to 5.9.4, this module affects the whole script, instead of inside its lexical block.

👀 See Also

perlunicode, perluniintro

open, utf8, encoding, Encode

✍️ Authors

Audrey Tang

©️ Copyright

Copyright 2004, 2005, 2006, 2007 by Audrey Tang <cpan AT audreyt.org>.

This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.

See <http://www.perl.com/perl/misc/Artistic.html>

---

perl v5.34.0 2026-06-23 encoding::warnings(3perl)

📛 Name 🚀 Quick Reference 🏷️ Version ⚠️ Notice 📋 Synopsis 📖 Description ⚠️ Caveats 👀 See Also ✍️ Authors ©️ Copyright