udp - phpMan

UDP(7) Linux Programmer’s Manual UDP(7)

NAME
udp - User Datagram Protocol for IPv4

SYNOPSIS
#include <sys/socket.h>
#include <netinet/in.h>
udp_socket = socket(PF_INET, SOCK_DGRAM, 0);

DESCRIPTION
This is an implemention of the User Datagram Protocol described in RFC768. It
implements a connectionless, unreliable datagram packet service. Packets may be
reordered or duplicated before they arrive. UDP generates and checks checksums to
catch transmission errors.

When a UDP socket is created, its local and remote addresses are unspecified.
Datagrams can be sent immediately using sendto(2) or sendmsg(2) with a valid desti-
nation address as an argument. When connect(2) is called on the socket the default
destination address is set and datagrams can now be sent using send(2) or write(2)
without specifying an destination address. It is still possible to send to other
destinations by passing an address to sendto(2) or sendmsg(2). In order to receive
packets the socket can be bound to an local address first by using bind(2). Other-
wise the socket layer will automatically assign a free local port out of the range
defined by net.ipv4.ip_local_port_range and bind the socket to INADDR_ANY.

All receive operations return only one packet. When the packet is smaller than the
passed buffer only that much data is returned, when it is bigger the packet is
truncated and the MSG_TRUNC flag is set. MSG_WAITALL is not supported.

IP options may be sent or received using the socket options described in ip(7).
They are only processed by the kernel when the appropriate sysctl is enabled (but
still passed to the user even when it is turned off). See ip(7).

When the MSG_DONTROUTE flag is set on sending the destination address must refer to
an local interface address and the packet is only sent to that interface.

UDP fragments a packet when its total length exceeds the interface MTU (Maximum
Transmission Unit). A more network friendly alternative is to use path MTU discov-
ery as described in the IP_MTU_DISCOVER section of ip(7).

ADDRESS FORMAT
UDP uses the IPv4 sockaddr_in address format described in ip(7).

ERROR HANDLING
All fatal errors will be passed to the user as an error return even when the socket
is not connected. This includes asynchronous errors received from the network. You
may get an error for an earlier packet that was sent on the same socket. This
behaviour differs from many other BSD socket implementations which don’t pass any
errors unless the socket is connected. Linux’s behaviour is mandated by RFC1122.

For compatibility with legacy code it is possible to set the SO_BSDCOMPAT
SOL_SOCKET option to receive remote errors only when the socket has been connected
(except for EPROTO and EMSGSIZE). It is better to fix the code to handle errors
properly than to enable this option. Locally generated errors are always passed.

When the IP_RECVERR option is enabled all errors are stored in the socket error
queue and can be received by recvmsg(2) with the MSG_ERRQUEUE flag set.

IOCTLS
These ioctls can be accessed using ioctl(2). The correct syntax is:

int value;
error = ioctl(tcp_socket, ioctl_type, &value);

SIOCINQ
Gets a pointer to an integer as argument. Returns the size of the next pend-
ing datagram in the integer in bytes, or 0 when no datagram is pending.

SIOCOUTQ
Returns the number of data bytes in the local send queue. Only supported
with Linux 2.4 and above.

In addition all ioctls documented in ip(7) and socket(7) are supported.

ERRORS
All errors documented for socket(7) or ip(7) may be returned by a send or receive
on a UDP socket.

ECONNREFUSED No receiver was associated with the destination address. This might
be caused by a previous packet sent over the socket.

VERSIONS
IP_RECVERR is a new feature in Linux 2.2.

CREDITS
This man page was written by Andi Kleen.