On Apache/1.3.41 (Unix) PHP/5.2.5 mod_perl/1.30 mod_gzip/1.3.26.1a
Under GNU General Public License
2008-08-20 19:11 @38.103.63.61 CrawledBy CCBot/1.0 (+http://www.commoncrawl.org/bot.html)
AVMCAPICTRL(8) Linux System Administration AVMCAPICTRL(8)
NAME
avmcapictrl - Add, reset or remove active AVM cards and load firmware
SYNOPSIS
avmcapictrl add <portbase> <irq> <type>
avmcapictrl load <bootcode> [<contrnr> [<protocol>
[P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]]
avmcapictrl reset [contrnr]
avmcapictrl remove [contrnr]
avmcapictrl trace [contrnr] [off|short|on|full|shortnodata|nodata]
avmcapictrl addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]
DESCRIPTION
avmcapictrl is used to register active AVM ISA cards kernelcapi system and there-
with to the isdn system. You need it also to upload the firmware to any active AVM
card. If an error occure please also check the kernel error messages by using the
command dmesg(8).
COMMANDS
add <portbase> <irq> <type>
is used to add a ISA card to the kernel-capi2.0 system. The portbase can have
the values 0x150, 0x250, 0x300 and 0x340 for the B1 ISA cards, look at the
jumper on the card. For a T1-ISA (HEMA) card you can select an wide range of
ports.
irq can be selected from the following values:
3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
type can be B1 or T1.
load <bootcode> [<contrnr> [<protocol>
[P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]] is used to load the firmware to a card
bootcode is a t4-file. The actual versions of the t4-files for the different
d-channel protocols can be found at ftp://ftp.avm.de/card-
ware/b1/linux/firmware.
You need different t4-files for different d channel protocols: b1-1tr6.t4 for
1TR6, b1.t4 for DSS1 and
b1-usa.t4 for 5ESS and NI1 (DSS1 is also supported).
For M1/M2 PCMCIA cards you need m1-s10.t4 or m1-s4.t4 depending on the handy
type used.
contrnr is the number of the controller (card) starting from 1.
protocol can be DSS1, CT1, VN3, AUSTEL, 5ESS or NI1.
P2P point to point
DN1:SPID1 DN2:SPID2 is for the american protocols 5ESS and NI1.
reset [contrnr]
is used to reset a card if loading has failed. This function only make sence
if card is not successfully loaded.
contrnr is the number of the controller (card) starting from 1.
remove [contrnr]
is used to remove a card previous added. You can also remove automatic added
cards (for example a B1-PCI card).
contrnr is the number of the controller (card) starting from 1.
trace [contrnr] [off|short|on|full|shortnodata|nodata]
is used to trace CAPI2.0 messages. The trace will be done as kernel messages,
see dmesg(8).
contrnr is the number of the controller (card) starting from 1.
off switch traceing off
short switch one line per CAPI2.0 message tracing on
on | full switch on full decode tracing
shortnodata switch on line per CAPI2.0 message tracing on, but exclude
DATA_B3_IND and DATA_B3_REQ messages.
on | full switch on full decode tracing, but exclude DATA_B3_IND and
DATA_B3_REQ messages.
addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]
is used to add a card, this is more generic than add.
driver currently b1isa or t1isa
portbase can have the values 0x150, 0x250, 0x300 and 0x340 for the b1isa
driver, look at the jumper on the card. For t1isa driver you can select an
wide range of ports.
irq can be selected from the following values: 3, 4, 5, 6, 7, 9, 10, 11, 12
and 15.
membase memory address if needed by driver
cardnr only usefull with driver t1isa
AUTHOR
Carsten Paeth <calle AT calle.de>
SEE ALSO
ttyI(4), isdnctrl(8), isdninfo(4). dmesg(8). syslogd(8).
4th Berkeley Distribution 2000/01/28 AVMCAPICTRL(8)
Generated by $Id: phpMan.php,v 4.55 2007/09/05 04:42:51 chedong Exp $ Author: Che Dong
On Apache/1.3.41 (Unix) PHP/5.2.5 mod_perl/1.30 mod_gzip/1.3.26.1a
Under GNU General Public License
2008-08-20 19:11 @38.103.63.61 CrawledBy CCBot/1.0 (+http://www.commoncrawl.org/bot.html)